AC110/220 to DC0-60V 8A Knob Switch Adjustable Power Supply Transformer for COB For Sale

When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

AC110/220 to DC0-60V 8A Knob Switch Adjustable Power Supply Transformer for COB:
$85.49

InputAC 110/220Voutput0-60V 0-8A480WCurrent VoltageAdjustable DC voltage stabilization switching power supply with digital displaySuitable for Our 100W/200W/300W COB LED, and our SMD3030 LED Panel Light, or other batteries charging, DC equipment, DC motor stepless speed regulation, LED electrodeless dimming, chemical electrolytic plating speed control, scientific research testing, student experiments, and so on, wide range of uses.Performance Description:

Input voltage:110/220VAC
Output voltage:DC 0-60V Fullyadjustable
Output current range:0~8A Fullyadjustable
Rated power: 480W
It has short circuit current limiting protection and automatic recovery function
Product switch power supply we send generally defaults to 220V shift. Please pay attention to the switching power supply working power switch position, if you need 110V, please switch to the correct gear
(How to limit current) to adjust the current?
1. in the case of power failure, the lower left corner of the small pull switch to adjust the current shift
2. the (special adjustable current plug) pulled out to the terminal port 2 and 3 ports, with a screwdriver to loosen the port screw, then use a screwdriver to tighten, (then connected to the electricity), connected to the next number The display voltage shows 0.00V, the current shows the current current parameters, then the power will be issued creak current small sound
3. in the right (adjust the current knob) can be transferred to the desired current limit parameters, and digital display synchronous display current parameters, 0-8A full adjustable
4. the (special adjustable current plug) removed, insert the original insert card holder, remove the rear display shows the voltage 0.90V or so, the current 0.00A
5. the lower left corner of the pull switch to the right to the \"open (use)\" stalls
6. the current power supply is just in the current limit of the parameter value, regardless of the power supply to a few V (digital display real-time display output voltage), the current constant, the use of current reaches 95% of the current limit parameters began to buck, Overload protection
7. then the digital display shows the current parameter is the current value of the device load, real-time monitoring of load current
Note that the power supply on the right side of the power (adjust the current knob) do not go to spin, after the rotation of the current limiting parameters with the knob rotation and change.If you do not need to limit the current, use the general equipment, without the above-mentioned operation, the lower left corner of the pull switch to \"open (use)\" gear, the (adjustable current knob) clockwise to the top, 8A.
Superiority：
- Products from the domestic professional switching power supply manufacturers, quality assurance, through professional testing,Buy it at ease.
- 100% full load test, to ensure that the power supply is more stable and durable, longer service life.
- With over-voltage protection, overload protection, high temperature protection, at the same time with the seismic resistance, pressure resistance.
- Product certification: CE
- Accord with EMC standard
- According to GB9254 EN55022 EN55024 class a design
Our Customer\'s Buyer Shows

For max current, if you choose 0-80v, when set the voltage at 24v, the max current still is 6A.

Operational use
(How to limit current) to adjust current?1. Operate in the case of power failure, pull the small pull switch in the lower left corner to the current regulating gear2. Pull out (dedicated current regulating insert) to the 2nd and 3rd ports of the wiring port, loosen the port screw with a screwdriver, and tighten with a screwdriver (at this time, connect to the listed power), and then connect The voltage of the meter shows 0.00V, and the current shows the current current parameter. At this time, the power supply will emit a small current.3. On the right side (adjust current knob), you can adjust the desired current limit parameter, and display the current parameter synchronously with the digital display. 0-21A/0-16A/0-11A/0-6.5A can be adjusted in the whole process.4. Remove the (special adjustment current plug) and insert it back into the original insert card holder. After removing the digital display, the voltage is about 0.90V, and the current is 0.00A.5. Pull the pull switch in the lower left corner to the right to open the \"open (use)\" position.6. The current power supply is in the parameter value of the current limit. The power supply is adjusted to a few V (the digital display shows the output voltage in real time), the current does not change, and the current reaches the current limit of 95% of the current limiting parameter. Overload protection7. The current parameter displayed by the digital display at this time is the current value of the device load, and the load current is monitored in real time.When the load device is connected, the current value can be adjusted directly in real time. The maximum current value is the maximum current value of the load device. If the current adjustment knob clockwise exceeds the maximum current value of the device, the digital current value will not last. Real-time synchronized digital display, showing only the maximum current value of the device.If there is no need for current limiting, use the general equipment, without the above operation, pull the pull switch in the lower left corner to the \"open (use)\" position, and turn the (current adjustment knob) clockwise to the top. The maximum current limit at this time is 21A/16A/11A/6.5A/4A, at this time the power supply parameter is the output which is equal to a 0-24V20A /0-36V15A/0-48V10A/0-80V6A/0-120V4A switching power supplyUses: Mainly used for various battery charging, DC equipment, DC motor stepless speed regulation, LED stepless dimming, chemical electroplating speed regulation, scientific research test, student experiment, etc., and a wide range of uses.Special attention: If using inductive load such as motor or fan, please pay attention to the maximum starting current parameter of the motor. This parameter must not be higher than the maximum operating current of the power supply. Otherwise, the power supply may be damaged. You should select a higher current power supply or soften the motor. The protection circuit is activated to absorb the inrush current.
Precautions:
*When the charger is used, please unplug the battery and turn off the input power. If it is not used for a long time, please store it in a ventilated and dry environment. *To ensure safety, please perform within the line of sight when charging. If you need to leave, remove the battery to avoid unpredictable danger. *Do not mix batteries of different types, different capacities and different manufacturers. * Keep away from flammable materials when charging, pay special attention to battery temperature. If the temperature is very high, such as hot, please disconnect the power immediately to stop charging. * Do not drop wires or other conductive objects into the charger. The consequences are self-sufficient. z Do not charge if the battery leaks, rises drum, peels off, changes color, or deforms. * Do not try to charge a non-rechargeable battery. * Do not exceed the charging range specified by the battery manufacturer.
*Do not modify or disassemble the charger. Turning on the machine and indicating that you have waived all warranty and technical

AC110/220 to DC0-60V 8A Knob Switch Adjustable Power Supply Transformer for COB For Sale

AC110/220 to DC0-60V 8A Knob Switch Adjustable Power Supply Transformer for COB: $85.49

Other Related Items:

AC110/220 to DC0-60V 8A Knob Switch Adjustable Power Supply Transformer for COB:
$85.49