DC 12V to 24V Large Torque Alloy Servo 100kg/cm for Mechanical Arm Robot For Sale

Description
DC 12V to 24V Large Torque Alloy Servo 100kg/cm for Mechanical Arm Robot

Parameter:
- Model:DS-SQ1.2AB360
- Rotation:270 degree
- Rated voltage:24V
- Rated current:3A
- Speed:40rpm
- Working voltage:12-24V DC(Any voltage between 12V and 24V can work)
- Static current:2mA
- No-load current:150mA
- Gear material:steel
- Size:103x60x92mm
- Weight:528gThe max torque:55kg/cm(12V)to 110kg/cm(24V)
Angle mode:Pulse signal(remote control,multi-channel servo controller,singlechip) or analog voltage signal(potentiometer)
Voltage signal input range:0V~+5VPulse signal input range:0.5ms--2.5ms,for all "multi-channel servo controller,aircraft model remote control,SCM programming,Arduino"The servo rotates when the remote control is on neutral point(the servo stops in neutral point),you can fine tun the trimmer potentiometer both clockwise & counterclockwise below the drive board.Application:middle/large size robot,mechanical arm and other large power large torque control areas.Power supply input:12V-24V DC(B- connects negative pole;B- connects positive pole)Mode select:Jumper cap setting pulse signal input or analog voltage signal input.PPM is pulse signal input,POT is analog voltage signal input.PPM is pulse signal input,POT is analog voltage signal input.Analog control mode:signal is analog value.You can rotate potentiometer to control motor output rotation and speed adjustment.(You can also adjust speed on VR1 trimmer potentiometer in circuit board)
1.For volatge:12V-24V
2.Rotation output shaft diameter:8mm
5.Full metal gear reduction motorThe Lion King Servo Description
(For the Lion King servos,all model)

Figure 2:Mode select:Jumper cap setting pulse signal input or analog voltage signal input (potentiometer).PPM is pulse signal input,POT is analog voltage signal input.The figure POT is analog voltage signal input,that is potentiometer,when the blue jumper cap jumps into ppm side,it’s pulse signal input,that is pwm signal.(The two jumper cap must jump at the same time.)

Figure 3:Mode select:5V output,or no output.The above figure:yellow jumper cap jumps 5V,the right 5V voltage output.When the jumper cap jumps to NC,the right 5V suspended,no output.When use potentiometer,need to switch to 5V output.

Figure 4:S is signal input,can input pwm pulse signal,can also use analog voltage input (potentiometer),GND input GND,can input owm pulse signal,can also use analog voltage input (potentiometer).GND input GND,input what signal,you can refer to Figure 2.

S interface is servo controlled PWM signal input interface,can input cycle 20MS,50HZ,pulse width is 1-2MS or 0.5-2.5MS standard servo control signal.If it can control normal servo signal,it can control our super servo,DIY servo.Please make sure the PWM signal is correct.S interface is used for connecting potentiometer and directly control motor angle,potentiometer feet (which have resistance change) connect S pin.The other two feet connect nearby two pins separately (exchange the two feet next to the potentiometer,it changes).

Mode select:The Figure 5 ms is used for switching PWM signal input pulse width,1-2ms or 0.5-2.5ms.Because servo control signal pulse widths are different,the function is used to switch.

For aeromodelling remote control receiver output PWM pulse width is 1-2MS.
If use it in 0.5-2.5MS mode,the angle can not reach 270 degree.It can jump to 1.0-2.0MS mode,evenif the pulse width is 1-2MS,the super servo the max angle can get 270 degree.But the market servo controls vary,some are 0.5-2.5MS output;some are 0.5-2.1MS output.These control signal are suggested to jump to 0.5-2.5MS mode.
0.5ms--2.5ms is suitable for multi-channel servo controller,some aeromodelling control,singlechip programming,“Arduino”.

Angle adjust:clockwise twist,the angle enlarges;anti-clockwise twist,angle decreases.The way to increase and decrease the angle is to increase and reduce both sides at the same time.Speed asjust:clockwise twist,the speed increases;anti-clockwise twist,speed decreases.Power interface:connect 12V-24V DC power,current choose 5A or more than 5A.In no-load condition,5A is OK.In load condition,suggested 10A or above 10A power supply.

Payment Terms
1.We accept PayPal only.
2.All major credit cards are accepted through secure payment processor PayPal.
3.Payment must be received within 7 business days of sale closing.
4.We ship to your or Paypal address. Please make sure your and Paypal address is correct before you pay.Shipping Terms
- For remote regions, we will charge your extra shipping costs. Usually it cost about 35USD-50USD. We will contact you after your payment. Thanks for your understanding.Return Terms
1. If you receive defective item, please kindly notify us within 14 days. We will guide you the returning instruction for replacement or refund.
2. If you purchased in improper condition, please NOTE that the sipping and handling fee will not be refund, all return shipping fee should paid by the buyer unless item DOA.
3. We reserve the right to refuse any returns for objective reasons.Custom Duties & Taxes
1. Import duties, taxes, and charges are not included in the item price or postage cost. These charges are the buyer's responsibility.
2. Avoiding some unnecessary trouble, please check with your country's customs office to inform us what we should declare its value before shipping.response
1. If you are dissatisfied for any reason, please don't be quick to leave us neutral or negative response. We work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave positive response to all our customers.
2. If you are satisfied with the product you received, please kindly leave us a positive response and 5 star DSR. If there is any problem of your order, please feel free to contact us firstly, we are responsible and credible seller, will follow it for you asap.