Heat.net

Heat.net Store Home


OmniTurn GT-75 CNC Turning Center (Lathe) For Sale


OmniTurn GT-75 CNC Turning Center (Lathe)
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

Buy Now

OmniTurn GT-75 CNC Turning Center (Lathe):
$32995.00

OmniTurn GT-75 Lathe

About OmniTurn

OmniTurn has been building precision CNC turning machines since 1987, beginning with CNC conversion kits for chuckers and toolroom lathes. We have always used the highest quality ground ballscrews and linear guides available. The machine base, slides and tooling plate are precision-machined in America

In 1994 we began producing the OmniTurn GT-75. The GT-75 is a fully enclosed slant-bed turning center with American-made high-precision spindle,pneumatic collet closer, flood coolant, and work lamp.

In 1998 we introduced the OmniTurn GT-Jr. The GT-Jr has the same rugged and precise base, table and spindle as the GT-75, but without the enclosure, which allows for very fast change-over and setup.

OmniTurns are fast, precise and affordable. They are also reliable, easyto operate and inexpensive to maintain. There are thousands of OmniTurns in use throughout the country earning a profit for large corporations as well as \'garage-shops\'.

We are able to offer this Brand New GT-75 for only $32,995.

More information is available here.

This machine was used only for software development and customer demonstrations.It is built entirely at our factory in Oregon. Easy setup! The GT-75 is shipped in a wooden frame as illustrated, for easy pallet-jack maneuvering into place in your shop.Air requirements are minimal: less than 3cfm at 80psi. Electrical power requirements are 220vac single or three-phase, 25 amps. The machine does not need to be bolted down. Leveling pads are included; simplyadjust each pad to stabilize the machine. You can set up your OmniTurn GT-75 with no special tools, and be ready to run parts very quickly.

Free telephone support and service weekdays 8am - 5pm Pacific Time (541) 332-7004.

Full one-year warranty on all parts.

OmniTurn GT-75 Standard Features Include:

  • Travel in X: 12\" Travel in Z: 9\"
  • Accuracy of slide travel: .0001\"
  • Resolution of slide travel: .00005\"
  • 5HP spindle drive
  • PC based control; holds thousands of programs
  • Standard G- and M- Codes
  • Gang tooling - 1/4 sec between tools
  • Pneumatic Collet Actuator; 5C Spindle
  • 1/8hp Flood Coolant System
  • 75 degree slant-bed lets chips fall away

SHIPPING

  • Buyer will pay ACTUAL COST by truck to anywhere in the continental US.
  • OmniTurn Factory will crate the machine and arrange shipping at no extra charge.
  • Call 541-332-7004 for shipping estimate to your location.

PAYMENT

We will accept Cashier\'s Check, Money Order or Bank Wire Transfer for payment .


Buy Now

Other Related Items:



Related Items:

OMNITURN GT-75 JR Series I CNC Gang Lathe G4 2015’ #GMT-3494 picture

OMNITURN GT-75 JR Series I CNC Gang Lathe G4 2015’ #GMT-3494

$24500.00



(2) Drawtubes from an Omniturn GT-75, one unused picture

(2) Drawtubes from an Omniturn GT-75, one unused

$300.00



Omni-Turn GT75, GTJr Machine Center Programming and Service Manual 1999 picture

Omni-Turn GT75, GTJr Machine Center Programming and Service Manual 1999

$325.00