STC-3018 Digital Temperature Controller Sensor Thermostat with NTC Cable For Sale

Brand 🆕 STC-3018 Digital Temperature Controller Sensor Thermostat (110-220VAC)

1、ABS flame retardant plastic shell, more safe to use. 2、Microcomputer intelligent digital display thermostat, dual display dual temperature.

3、The large and clear digital display shows measuring temperature, high accuracy of temperature measuring and controlling.

4、Suitable for automatic switching of refrigeration and heating devices such as seafood machines and cooling water machines.

Specifications:

Display Type: Digital

Temperature sensor: NTC 10K

Senor length:1.0m

Temperature measuring range: -55 ° C ~ 120 ° C / -66°F~248°F

Resolution: 0.1 ° C

Accuracy:±1° C

Power supply: 110-220VAC

Power consumption: <3W

Storage temperature: -30 ° C ~ 75 ° C

Relative humidity: 20% ~ 85% (No condensate)

Relay contact capacity: 10A/240VAC; Heat 10A/240VAC

Instruction:

Normal mode: The red digital tube on the left shows the real-time temperature, the blue digital tube on the right shows the set temperature.

Setting mode: The red digital tube on the left displays the setting mode, the blue digital tube on the right displays the setting contents.

Instructions:Normal mode: The red digital tube on the left shows the real-time temperature, the blue digital tube on the right shows the set temperature.Setting mode: The red digital tube on the left displays the setting mode, the blue digital tube on the right displays the setting contents.P0: working mode
This setting is mainly set to the value when the thermostat is used for the first time. If it is used for heating, it should be set to H. If it is used for cooling, it should be set to C.
P1: hysteresis setting
The hysteresis is the difference required when the thermostat reaches the set temperature and stops working again. For example, if we set the heating mode to a temperature of 37-40 degrees, then the difference is 3
P2: high temperature alarm value
When the temperature reaches the set value, there will be an alarm action and stop working.
P3: low temperature alarm value
When the temperature is lower than the set value, there will be an alarm action and stop working.
P4: temperature correction
These functions are used for temperature calibration. If there is a deviation between the detected temperature and the actual temperature, some functional effects can be used. The positive value = measured value + corrected value. For example, we measure the temperature at 25.6 degrees and actually 25.8 degrees. P4 can be used. Set to 0.2 then the final temperature is 25.6+0.2=25.8
P5: delayed start
This function is generally used for compressor refrigeration. If you purchase some thermostats for the refrigerator freezer, this value must be set. According to the compressor back pressure, the general setting is 3-6 minutes.
P6: C/F conversion
If you want to change to F value, change the unit to F, the unit display light is on. If you want to change it to C value, change the unit to C, the unit display light is not bright. If you want to convert quickly, exit the display, long press You can quickly convert units by adding 3 seconds.
Package Included:1 x STC-3018 110V Dual LCD Digital Temperature Controller Thermostat1 x Probe SensorInstructions/schematic are NOT included. We don't provide technical assistance please make sure that you are familiar with the product before purchasing.Operating instructions
To operate: Press the RST (reset) button for 3s to start the thermostat. Press again for 3s to turn it off. When the power is applied, the thermostat switches on automatically.
Normal mode: The red digital display on the left shows the real-time temperature, the blue digital display on the right shows the set temperature (i.e. when to start the load device). To establish the set temperature reference (blue display), press 'S' (set) once, the blue display will flash, then press up/down to set to the desired temperature (hold down the up/down button to quickly adjust temperature range).
Change settings: Pressing the 'S' button for 3s puts the Controller in the setting mode. The red display will show the setting code (see below codes: P0-P6); the blue display will show the code’s parameters. Once you are in setting mode, use the up/down buttons to select the desired code on the red display, then press 'S' once; this will flash the blue display, where you can then adjust the parameters using the up/down buttons. Tip: after a few seconds of no activity the controller will revert back to the normal display, so adjust the settings quickly!