Belimo Kit to Replace Honeywell M847D Series Motor on Honeywell ZD & ARD Dampers For Sale

*Works as a replacement for Honeywell M847D series motors on popular ZD and ARD dampers, including M847D1004 and M847D1012 motors and other M847D series motors. *Works as a replacement for Trol a Temp MSR, RDMH, and other dampers.*Works on many 24vac dampers from Honeywell, Trol a Temp, AprilAire, ZoneFirst, EWC, Robert Shaw, Research Products, Ztec, Buetler, Durozone, and others with a 3/8" or smaller drive shaft (other kits available for other size drive shafts - see our damper motor retrofit kit listings in our damperdirect store.*Works as a 24 volt replacement on any damper with a round drive shaft 3/8" or smaller in size
Our store damperdirect has many other retrofit kits and adapters to get almost any damper back in business - your satisfaction is guaranteed!
This listing includes the Belimo LMB24-3-T motor, shaft adapter, anti-rotation bracket and two self tapping sheet metal screws - anything else in the picture is for illustration purposes.
Tired of replacing spring return damper motors that get hot and burn out? The Belimo to Honeywell Retrofit Kit BHK-24 gets the the premier commercial grade Belimo LMB24-3-T damper motor and adapter kit for about the same price as the Honeywell M847D1012 two wire spring replacement motor. This kit will also work on virtually any other damper that has a shaft under 3/8" in diameter.
*Retrofits the industry-leading LMB24-3-T motor on to many residential dampers, including Honeywell, Suncourt, Robert Shaw, Invensys, AprilAire, Research Products, Perfect Temp and any other damper with an external driveshaft 3/8" or less in diameter.*5 year warranty*Gets rid of spring return motors for better reliability and energy savings.*Works with any brand of standard 24vac zone control system.*Saves energy and extends motor life with a far more powerful motor, backed with 5 year warranty.*Requires three wires to motor and the mounting of the anti-rotation bracket with two self tapping screws, included.*24vac 2 va damper motor
Spring return damper motors pull 8 to 10 va of continuous power since they must overcome the return spring. Besides wasting energy, the spring return motors get very hot, contributing to their often premature failure. The Belimo LMB24-3-T retrofit kit motor uses just 2va for 90 seconds, never even gets warm to the touch, and is covered by a 5 year, best in the business, warranty. So stop replacing those overpriced spring return motors!
You may be thinking - my current damper has just 2 wires to the motor, will this 3 wire motor work? Yes, but you will need a 3rd wire from the zone control panel or thermostat to allow this 3 wire motor to work. Very often, standard 4 wire thermostat wire will have been used, so check the cable for extra wires. Most zone control panels support 3 wire motors, including all Honeywell panels - check your zone control board damper outputs for an unused terminal. If your damper outputs are labeled M1, M4, and M6, OR Power Open (PO), Power Close (PC), and Common (C), you have all the outputs you need and are good to go. Even if your zone panel has just 2 damper outputs, you can still use this kit since the Belimo LMB24-3-T motor will accept an alternative wiring procedure that places full time 24vac power on terminals 1 and 2, and then uses the current zone board output for terminal 3. Full illustrated instructions are included and we're here to help you with technical support through messaging.From damperdirect, where zoning is our only business! We offer the service, support, and technical resources to help you design or service your Zone Control System.
We handle all major brands, including RetroZone™, Honeywell, EWC, Durozone, Enerzone Systems Corp., Robertshaw, Invensys and more. If you don't see it on , please message us via and we can get you the part you need. Please also message us via for technical support and/or application questions.