When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
FCC ID#(s)
for FCC ID FCCID M3N65981403
Alternate Spellings
for M3N6598i403 M3N659814o3 FCCIDM3N65981403
for FCC IDM3N65981403
Part #(s)
Dealer #(s)
FOR THIS FCC ID / PART #
2005 2006 2007 05 06 07 for Chevy for Chevrolet Corvette
Button Count
5: Unlock, Lock, TRUNKOpener Release, Panic Alarm Horn
Battery (installed)
1; CR2032
Frequency
315 MHz (315MHz)
Programming:
Please note not all customers will be able to complete the programming on their own so if you are having trouble or unsure diagnostic programming is available at your local qualified automotive locksmith or car/audio shop.
How to Program a 2005 for Chevrolet Corvette Keyless Entry Remote Fob Smart Key
Step by Step How to Programming Instructions:
Programming with a recognized Transmitter:
Canadian owners see locksmith or dealer.
IMPORTANT: This procedure is not available when the maximum number of 4 fobs have been programmed. If 4 key fobs are programmed to this RCDLR and this method is attempted, the driver information center (DIC) will display, MAX FOBS LEARNED and the programming procedure will exit.
This procedure will add key fobs. Fobs will be numbered in sequence based on when they are programmed; if 2 fobs are currently programmed to the RCDLR, a fob programmed using this method will be numbered as Fob 3. This procedure requires that you have a known good key fob, a replacement key fob, and the vehicle\'s mechanical key.
1. The vehicle must be off.
2. Place a known key fob and the new un-programmed key fob within the interior of the vehicle.
3.At the rear of the vehicle, insert the vehicle key into the rear compartment lock cylinder, located above the license plate. Open the trunk and cycle the key 5 times within5 seconds.
4. The DIC will display: READY FOR FOB X (X = fob 2, 3, or 4).
5. Place the new un-programmed key fob in the glove box fob pocket with the buttons facing passenger side.
6. A beep will occur and the DIC will display:READY FOR FOB X (X =fob 3 or 4) orMAX FOBS LEARNED.
7. Press the OFF/ACC portion of the ignition switch to exit programming mode.
8. Test remote.
Programming without a recognized Transmitter:
Canadian owners see locksmith or dealer.
1. The vehicle must be off.
2. Place the new un-programmed key fob in the glove box transmitter pocket with the buttons facing passenger side.
3. At the rear of the vehicle, insert the vehicle key into the rear compartment lock cylinder, located above the license plate. Open the trunk and cycle the key 5 times within 5 seconds.
4. The DIC message will display OFF-ACCESSORY TO LEARN.
5. Press ignition switch.
6. The DIC will read WAIT 10 MINUTES and will count down to zero, one minute at a time.
7.The DIC will display OFF-ACCESSORY TO LEARN again.
8. Press ignition switch.
9. The DIC will read WAIT 10 MINUTES and will count down to zero, one minute at a time.
10. The DIC will display OFF-ACCESSORY TO LEARN again.
11. Press ignition switch.
12. The DIC will read WAIT 10 MINUTES and will count down to zero, one minute at a time.
13. A beep will sound and the DIC will read READY FOR FOB #1. At this time, all previously programmed key fobs have been erased.
14. Once the key fob is recognized and programmed, a beep will sound and the DIC will display READY FOR FOB #2.
15. If you have additional key fobs to program, take key fob #1 out of the transmitter pocket and place key fob #2 in the pocket. This can be done repeatedly until up to 4 key fobs have been programmed. The DIC will then display MAX # FOBS LEARNED and will exit the programming mode.
When you are done programming key fobs press the ignition switch.
Condition Notes
NEW; ready to be programmed to your vehicle’s compatible factory installed RKE system
